1. Operating Precautions

1) Since front polarizer is easily damaged, please be cautious and not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
5) Since the panel is made of glass, it may be broken or cracked if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open nor modify the module assembly.  
8) Do not press the reflector sheet at the back of the module to any direction.  
9) In case if a module has to be put back into the packing container slot after it was taken out from the
container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CCFL
Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT Module.  
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not twist nor
bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration
that no bending/twisting forces are applied to the TFT Module from outside.  Otherwise the TFT Module
may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or
regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be
supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied
exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or UL1950).
Do not connect the CCFL in Hazardous Voltage Circuit.
15) Severe temperature condition may result in different luminance, response time and lamp ignition voltage.
16) Continuous operating TFT-LCD display under low temperature environment may accelerate lamp exhaustion
and reduce luminance dramatically.
17) The data on this specification sheet is applicable when LCD module is placed in landscape position.
18) Continuous displaying fixed pattern may induce image sticking. It ’s recommended to use screen saver or shuffle
content periodically if fixed pattern is displayed on the screen.

G104SN03 V1 rev.1.2
5/25
AU OPTRONICS CORPORATION

Product Specification
G104SN03 V1

2. General Description
G104SN03 V1 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD display, a driver circuit, and
a backlight system. The screen format is intended to support SVGA (800(H) x 600(V)) screen and 16.2M (RGB
8-bits) or 262K colors (RGB 6-bits). All input signals are LVDS interface compatible. Inverter card of backlight is
not included.
G104SN03 V1 is designed for industrial display applications.

2.1 Display Characteristics
The following items are characteristics summary on the table under 25 oC condition:
Items
Unit
Specifications
Screen Diagonal
[inch]
10.4
Active Area
[mm]
211.2(H) x 158.4(V)
Pixels H x V

800x3(RGB) x 600
Pixel Pitch
[mm]
0.264 x 0.264
Pixel Arrangement

R.G.B. Vertical Stripe
Display Mode

TN, Normally White
Nominal Input Voltage VDD
[Volt]
3.3 (typ.)
Typical Power Consumption
[Watt]
3.5W (IRCFL=4.5mA)
All black pattern
Weight
[Grams]
300g(typ.)
Physical Size
[mm]
236.0(H)x 174.3(V) x 5.7(D) (typ.)
Electrical Interface

1 channel LVDS
Surface Treatment

Anti-glare, Hardness 3H
Support Color

16.2M / 262K colors  
Temperature Range
Operating
Storage (Non-Operating)

[oC]
[oC]

-20 to +70
-30 to +80
RoHS Compliance

RoHS Compliance                          

1. GENERAL DESCRIPTION
1.1 OVERVIEW
G104X1- L04 is a 10.4” TFT Liquid Crystal Display module with LED backlight unit and 30-pin-and-1ch
LVDS interface. This product supports 1024 x 768 XGA format and can display true 16.2M colors (6-bits
colors with FRC). The converter module for LED backlight is built-in.

1.2 FEATURES
- Excellent brightness (500 nits)
- Ultra high contrast ratio (1200:1)
- Fast response time (Ton+Toff average 25 ms)
- High color saturation NTSC 57%
- XGA (1024 x 768 pixels) resolution
- DE (Data Enable) only mode
- LVDS (Low Voltage Differential Signaling) interface
- Ultra wide viewing angle: 176(H)/ 176(V) (CR>10) Super MVA technology
-180 degree rotation display option
-LED Light Bar Replaceable
-Wide operation temperature
1.3 APPLICATION
-TFT LCD monitor  
- Industrial applications


1.4 GENERAL SPECIFICATI0NS
Active Area :210.4 (H) x 157.8 (V) (10.4” diagonal) mm
Bezel Opening Area :215.4 (H) x 161.8 (V) mm
Driver Element :a-si TFT active matrix
Pixel Number :1024 x R.G.B. x 768 pixel
Pixel Pitch (Sub Pixel) :0.0685 (H) x 0.2055 (V) mm
Pixel Arrangement :RGB vertical stripe
Display Colors :16.2 M color
Display Operation Mode
Transmissive mode / Normally black
Surface Treatment :Anti Glare
Total power consumption (typ) :10 W

1. GENERAL DESCRIPTION
1.1 OVERVIEW
G104X1- L03 is a 10.4” TFT Liquid Crystal Display module with LED backlight unit and 30-pin-and-1ch
LVDS interface. This product supports 1024 x 768 XGA format and can display true 16.2M colors (6-bits
colors with FRC). The converter module for LED backlight is built-in.

1.2 FEATURES
- Excellent brightness (350 nits)
- Ultra high contrast ratio (1200:1)
- Fast response time (Ton+Toff average 25 ms)
- High color saturation NTSC 57%
- XGA (1024 x 768 pixels) resolution
- DE (Data Enable) only mode
- LVDS (Low Voltage Differential Signaling) interface
- Ultra wide viewing angle: 176(H)/ 176(V) (CR>10) Super MVA technology
-180 degree rotation display option
-Color reproduction (Nature color)
-Wide operation and storage temperature range (-20℃ to 70℃ operation, -20℃ to 80℃ storage)

1.3 APPLICATION
-   TFT LCD monitor for Industrial applications
Slim design display for portable applications  
Digitizer Applicable Design

1.4 GENERAL SPECIFICATI0NS

Active Area :210.4 (H) x 157.8 (V) (10.4” diagonal) mm
Bezel Opening Area :215.4 (H) x 161.8 (V) mm
Driver Element :a-si TFT active matrix
Pixel Number :1024 x R.G.B. x 768
Pixel Pitch (Sub Pixel) :0.0685 (H) x 0.2055 (V) mm
Pixel Arrangement :RGB vertical stripe
Display Colors: 16.2 M color
Display Operation Mode :Transmissive mode / Normally black
Surface Treatment :Anti Glare
Total power consumption(typ) :5.1 W

3.8*3.8*12mm,10uH